Historic doorsThose old doors add so much architectural charm to your Denver historic home that you just can't find in a new door. However they may be hard to close, or even need to be slammed. This is due to many factors such a settling of the house, paint build-up, loose glue, loose hinges and/or warping of the door itself. Old doors can be restored so that they open and shut just as nicely as their counterparts in newer houses. Do not be like many home owners and try to solve the problems with half done repairs. Do it right, and here's how;

Paint Buildup

Paint buildup is the most common cause of doors that won't shut cleanly. The nice little gap between a door and its frame gets a bit narrower each time the door is painted. Eventually, with enough layers of paint, the gap disappears entirely. Luckily this is an easy thing to fix. Just remove the built-up paint with a heat gun, a scraper, or chemical remover. If you're using a scraper, take care not to gouge the edge of the door. And keep in mind that you need to remove paint in two places -- the edges of the door, plus the part of the door frame that the door closes into.

Loose screws

Sometimes doors bind because their hinges are loose. To learn if this is the case, open the door part way, and then jiggle the door toward and away from its hinges. If the hinges move, they're loose. Tightening the screws may be the only fix needed but sometimes the screw holes are stripped. If that's the case, and the loose screws are on the part of the hinge that is attached to the door, you can use longer screws to re-secure the hinge to the door. Just make sure to use screws with heads that are small enough to fit flush with the hinges.

Open Joints

Open joints between a door's rails and stiles are another common problem. The cure is pretty straight forward. Structurally, old doors are made out of stiles, these are the vertical boards in a door, plus rails, the horizontal boards, plus recessed panels. Tenons, small pieces of wood, jut out of the rails and into the stiles forming the joints that hold doors together. Sometimes tenons come straight through the door so that you can see them when you look at the vertical edges of the door. Sometimes, especially on newer, machine-made doors, the tenons are invisible because they come only part of the way through the stiles. These are hidden tenons. The tenons stay put, or at least they're supposed to, through a combination of glue and either pegs or wedges. Over time the glue holding the tenons tends to wear out. When this happens, gaps begin to open up between the door's stiles and rails. These gaps may be quite visible when you look at the door. Or they may be hidden behind layers of paint, caulk or other things earlier owners stuffed into these gaps to hide them. Either way, the effect of the gap is that the door is somewhat wider than when it was first hung. And that means it won't shut. To fix these gaps, first determine if your door has through tenons or hidden tenons. For a through-tenon door:
  • First, remove the paint and other gunk from the joints .
  • Next, take a close look at the edge of the door. You should see a wedge, or sometimes a pair of wedges, that help hold the tenon in place.
  • You need to remove these wedges. You should be able to work them free by gently tugging at the open joint and then pushing it closed a couple times. Once they're out, cut new wedges -- slightly longer than you'll need.
  • Next, work as much carpenter's glue as possible into the joint. Then put some glue on the new wedges and drive them into place. And then clamp the joint tight until it dries.
  • Once the glue is dry, chisel the ends of the wedges so they're flush with the door .
To fix a door with hidden tenons:
  • First, work the loose joint back and forth a bit to open it up as much as possible,
  • Then work as much new glue into the joint as possible and clamp it.
  • Sometimes this will fix a door for a long time ... but sometimes not.
  • If this fix doesn't hold (or, if you want to fix the joint once and never have to worry about it again) you can drill pilot holes and then drive a pair of long wood screws through the edge of the door and into the stile. This will hold everything together snugly. And, for clean work, counter-sink the screws, and fill over their heads with putty.
DOWD Restoration has restoration experience from repairing worn and damaged doors to restoring historic architecture to both private homes and commercial properties. Refurbishing a timeworn, derelict or mistreated piece of the past and renovating it for future generations to relish is tremendously satisfying work. Let DOWD Restoration help you with your next historic restoration project! Find more helpful restoration ideas here.